Buying a Used Compact Excavator in the 2018–2021 Window: Undercarriage Wear Check Before You Wire Funds

They had been turned, by somebody. Each of the joints pressed out, a 180 turned, pressed back in. This re-creates the outside“wear surface”and doesn’t do the other half of the wall thickness. Simple. Brutal. The buyer demanded good currency for a chain, cosmetically resurrected, and the documentation proved to be ideal in this regard, for documentation simply documents a chain’s hours.

To be honest, the turned-bushing trick’s not that uncommon in this window—or even an immoral practice in all circumstances—some fleets turnover bushings as scheduled maintenance and do so. The form of every problem is interval. When turned at the proper time, it will prolong the life of the chain(s). Its product turns on a chain with pins that have ovaled their bores to yield a structure that is decorated with beautiful outside diameters. The amount of wear that the caliper exerts is the wear that the seller can see that he or she wishes to reach.

The tells are in the joints and if dirty enough, then they can be read. The bushing seam is always in the same orientation with respect to the pin; after a true turn the seam is in a different position in all the joints–this is acceptable once at identified point, but what if the outer surface of the bushings was already in their hardened layer? Slide a gloved thumb over each bushing, and feel a smooth flat glossy work-hardened ring along each bushing where the polishing action of the sprocket has been at work. Pressure washing is performed on a freshly turned set, in which case a knife drag band will not be present and the finish will be a uniform matte (chalky) texture and the grease will have been washed off in order to ensure the set looks like new. Not so easy is that an all-new chain is the same. The only thing that is different is the mark that is made by the press.

Examine the end with the outer link to the bushing. The face of a factory pressed item is smooth with the chamfer machining still visible with just a slight dished face. The witness marks of the shop press are the small radial scratches from the mandrel that’s just not quite right, the burr that rolls over one side and sometimes a band of fresh grease, rolling out of the joint for weeks afterward, even after all the grease has been washed out. I have used flashlight and counted the marks on the stamps of the blocks and then announced the number in front of a 2019 three-tonner, whose reaction was face changing. He knew. He was praying that I wouldn’t crawl.

Worn chain makes a different sound than a good chain. Set the bucket down on its side so that the boom is more off the ground than flat and slowly rotate the chain by hand (a well bucket makes a strategy-free, dull even rumble with each roller rolling under the links). The next note you’ll hear is a hollow knock that happens every time a joint gets into a valley that it doesn’t fit into and that fuller the joint is of return to the sprocket, the louder it knocks; that’s a stretched chain with a worn out sprocket. I was told that knock about a 2018 unit even before I measured back then with the calipers, and all the measurements after were just affirmation to the ear.

The Hours Field Is Not a Wear Record, it’s a Filing Label

Two machines can leave the same rental yard, ride the same number of hours and end up at your inspection with two seasons difference in the undercarriages and it is no mystery why! Hours are a measure of number of revolutions of an engine at load. Various factors that the meter is not able to “see” are responsible for under-carp operations: Track surface, frequency of turns, operator’s habit, and the load in the bucket while the machine travels. The unit which has always worked on finished concrete trenching’s utility shows practically no chain wear after two thousand hours. When one track starts to fatigue due to the same two thousand climbing a gravel stockpile and pivoting to dump, so do the chain, sprockets, idlers and rollers.

2015 Komatsu PC35MR Mini Excavator

Set chain tension first–all that which follows must follow–and few do it. The chain that is slack, reads long, and the chain that is tight reads short, and the error direction is toward the seller, so the measurement should be made on a warm chain, level ground, setting the tension to a manual setting, not what it happens to be set at. My calculations are 10 links round the loop pin center to pin center, as chains have an even wear and the worst wear is the honest number.

The nominal pitch for a compact class chain is in the regions of seventy-two to seventy-eight millimeters based upon the size class of the chain. After about 1.5% above nominal on a working machine, I begin to inquire for documentation for the replacement machine. When the chain letting up of sprockets climbs out of the tooth valleys under load, it’s a 2 percent, or greater with corresponding sprocket root wear, chain. The chain goes up, the profile can no longer keep the chain, so it falls to mid-swing with a full bucket and the one time you don’t have enough cash–on top of someone’s trench box. Those bands were under my own yard conditions when warm and I would not stand behind to two decimals under anyone else’s yard conditions.

The percent buyback actually resides in what it buybacks. As elongation is increased, load per tooth engagementwill increase since fewer teeth are actively handling the load at any one time. It will speed up tooth wear, increasing the effective pitch again, and the cost of the consumable group (not just the chain) will be lost! When a seller counteracts a pitch number he believes he’s making a counter-argument over one portion.

Check tooth height at the root of the tooth with regards to a new tooth reference point on frontal face tooth where bushing bears. Not at the end, everyone’s common end to take pictures. Once the root is scooped out the tip still appears sharp. I put a straight edge over two opposite teeth, squat down and reach down to the valley of the sprocket to the caliper, and know how much more or less the tooth variation is over the caliper, rather than the absolute amount—an evenly worn sprocket wears in a predictable manner, a sprocket worn into a pattern was running on a stretched chain.

Then there is the trick and I have witnessed it working with the experienced buyers. When a freshly washed sprocket is raked in this way from a low angle, (using a phone flashlight), the scope of the lay of the land is as crisp and sharp as it can get—you’re raking the leading side of a scooped out valley which is thrown as a hard shadow that your eye treats as a tip. Turn to the other side and strike a match on this. The valley becomes level, the tooth becomes blunt and the true tooth comes to light. Twice, on both sides, every time, I do not think I ever grudge the 90 seconds.

Consumable Group Price It That Way

Color gradient will show on the Roll body to indicate how long it’s been running. Fresh leakage is thin and dark in colour and dust is deposited on it to form an even grey-black film. Older leakage is usually cooked off volatiles, varnished and amber brown–it will not clean off with a rag, and will take a scraper, and the location relative to the grease setting is indicative of whether the operator was refining the grease job at all, or only greasing the fittings he could access standing up.

The other half is Idler flange thickness and is the measurement people don’t do as it requires getting under the vehicle. The internal structure of the lip erodes off from the inside out as the internal links rub the surface during turns–the visible outer part of the lip does not lose any structure but merely cosmetically wears down. Using gloved thumb, check for knife edge by running over lip. A good flange is a rolled over blunt flange that will not offer resistance to the chain. Then, when it’s worn thin enough to cut, it no longer guides the track on a side slope–and that’s when you begin tossing chains on side slopes you used to walk through on it.

The key to good practice in avoiding buyers pitfalls is to avoid component by component negotiating and cease and start to add up percentages of a complete undercarriage rebuild. Chain at 50% worn, sprockets at 50% worn, rollers at more than 50% worn, idlers at 33% worn plus bushings that only have 1 rotation before being semi worn: all are over 50% written off within 1 work season and it’s total cost that you need to be considering, not just the most expensive item. These bands are not survey data but represent my judgment and I’ve shifted them from one machine in rock to one in loam.

Now you do have the arithmetical you have to use. Ten links (pin to pin center) on a hot chain at proper tension; tooth heights measured at base and total percentage for the group (not the poorest single tooth). All this doesn’t require a specialist physically. Requires calipers, straight edges, flash lights and a low knees position while being watched by the seller.

Share this article

Table of contents

Kevin Chen

Chen Kaiwen holds a bachelor’s degree. He frequently travels to construction sites around the world to provide customers with high-quality excavator repair and maintenance services.

Professional excavator technical support and purchasing services

The machdealers platform provides high-quality services for your excavator purchase, repair, and after-sales support.