Hydraulic Abuse on Compact Excavators: Breaker and Auger Duty Nobody Discloses

My first sighting was when the boom had been repainted. Walkaround 1 handed, chicken sandwich in my left hand was going stale. 2900 hours accumulated using the meter. Property use, the seller told me–a gentleman with a horse paddock. Tight undercarriage, boom paint has a good zest of reducer, seat vinyl is not cracked.

Low hour machine will be in paddock, repainted boom is not a crime. The Auxiliary circuit convinced me to place down the sandwich.

Both‘quick couplers’ were capped, whereas most used iron managers just have one. Then I grabbed on to a cap and peeked at the female end and in 4 seconds, everything was different. It was a brass burnish on the nose–look, I’ve been push pushed in the nose and twizzled out and twizzled out a few hundred times. The dust plug was fabricated out of a hardware-store black rubber, wrong profile, loose in a coupler which required a particular OEM cap. Nothing looks worse on a man or woman paddock job than a coupler face.

Which I’ll over-explain, because no one thinks of it in terms of price. An O-ring used in a flat-face coupler, on the female half of the coupler. It is in a counterbore, is supposed to seal against the flat face of the male part and is apparently expected to withstand compression and release each time the next guy connects a breaker, the oil impinged against the back side of it, and whatever the last guy sprayed on it.

A healthy one feels like it’s something that is not supposed to be that way to a beginner. Try putting your thumb into it, it gives and bounces back and pulls a little bit on the skin when it’s dry. If is fails then it is a different object! It goes hard. Not stiff—hard, like a nylon washer, and dropped on the bench it makes a small flat click sound, rather than plopping on the bench. This click is known as compression set plus heat aging. The nitrile will no longer “remember” its ability to form an elastomer seal when closed on a flat face, and will no longer seal as such when closed against pressure. I’ve pulled ones that split themselves in half between my fingers and the side that was broken was shiny not torn from hitting as it does on mechanical damage.

This results in the absence of blowout. Worse. Quiet. The face seal is also hardened; it is damp when under pressure and dry when not; it gives the appearance of a coin size patch and nobody cares because of the seal at rest. In the meantime it provides the air circulation for the circuit. There is air in a hammer circuit causing the breaker to operate hot and to cavitate the pump on the return side. When no one was paying any attention to the coupler O-ring is worn into the pump, the pump wears, the debris becomes the filter I’m cutting open later in this piece. For less than the cost of a sandwich–and replaced–about never!

The factory crimps are always on a single set of die impressions, uniform ferrule at a certain distance from the insert end and uniform sleeve extrusion. The different ferrule profile for field re-crimps is due to the fact it was re-crimped by the local shop with what they had available, and had a slight step where the insert was re-pushed back into the hose.

As soon as I see one re-crimp on one assembly, I don’t want to know why. One is a manufacture fault/chafe event–both occurred on a ‘paddock machine’ is an equal possibility. Seasons apart, two, and on a compact excavator it’s likely to be one of the attachments that is causing a hose to be at pressure.

If you notice one or more rings around the circumference at mid-stroke, then it is likely that the wiper is grinding a ring where the rod is. It is from end to end with the scratching going in the same direction as the movement of the rod, under load with something against it, repeated along the movement. It is quite a tough experience already for any cylinder that is adapted as a dozer, a jack and a stabiliser—and usually used during the same hour by the same operator on the same blade.

That reminds me of a real stupid incident several years ago, a guy that used to run a breaker on a three ton piece of equipment who“balanced”it by attaching a counterweight to the blade, and still wondered what the problem was if he was getting a new blade every six months. Absurd. He stopped for the cylinders, he didn’t stop for himself.

Greased rods are a sign of a grease gun and 30 seconds. This covers up the actual fault the thumbnail had.

Tight-tail machines are those which are inverted (offset cylinder with a sealed land facing upwards), thus causing these to be missed. There is no dripping from the seepage. It will sit in the wiper recess area and cook against the wiper rod and form an integral dark dust ring above the seal which requires holding the torch low and inclined to it. It is accessible as a shadow from standing position.

The offset play is confirmed by pin play at the offset joint. That joint cannot resist hammer duty loads, and, clearance takes up quicker than will grading. With the machine turned off, rock the boom tip until you feel “clunk”, your dead, small, band is forward of a clunk, not a loose pin, which is a worn bore.

There’s a reason I have a c-frame can cutter behind my seat. There is nothing on the outside to indicate that this is a return filter.

Make sure to cut on this date code located on the can. Fresh date, clean pleat pack on high hour machine is not clean machine—it’s a cleaned machine.

Bronze looks copper-pink to dull brown, and is not attracted by the magnet. Almost invariably it is actually detached from the pump rotor group or a wear plate on compacts. Form beats quantity. Flake: a wearing face that is flattened, leaf-like and is on the surface. A chip, a sliver is not something wearing, it’s something that fails.

I assume I am not going to be able to count, I grade size by eye to a known size. It’s important within the span of an arm to see through a shop window. Machines that require an oil sample are a good buy if they’re clearly visible out of the way when a pleat is set at an angle to low sun. When people use a particle count as the quote for not observing anything with the naked eye they delude themselves into believing that they haven’t earned any more.

Light bronze sheen: a machine that tells a story. A machine with a bill coming that produces flakes of bronze.

Retrieve the details in the relief settings and loaded test.

This is done when somebody wants to “walk off the pain” with a tired pump, by over shimming the main relief to maintain reasonable cycle time, offloading wear problems to the cooler and its seals, and hose assemblies that were not sized for it.

Dressed in cold oil, a worn pump looks good. Needle moves, stays on and everybody shakes hands and leakage past a worn rotor group is low while viscosity is high. Run the machine for 40 minutes hot by doing the job, not idling around, and this same pump shows different readings. Needle does not reach up to spec. This flutter is related to engine rpm and not load, and hence is an internal leak and not an external restriction. As soon as it is released, the gauge takes a beat to settle.

Two seasons later the man who took the repainted machine called. The first thing he said was that the house was fine, the paddock was fine and that the boom was still the prettiest thing on the place. Second thing was: Question was on the pressure gauge which will not hold.

Conclusion

You’re equipped with the procedure now. Thumbnail on the rod at the seal land, torch light held low across the offset wiper, a coupler face checked to see if it’s burned not if its caps, and a filter can is opened with a magnet drawn through the pleats. No special tooling.

There’s no difficulty with doing it on one machine. When buyers get to 11 machines and 4 yards, and each seller with a paddock, is where they give up and buy based on paint and yardage. Not that the buyer didn’t have the test, but that he did not use the test, and that is quite costly.

Use your own thumper. We would prefer you check rather than trust us!

Share this article

Table of contents

Kevin Chen

Chen Kaiwen holds a bachelor’s degree. He frequently travels to construction sites around the world to provide customers with high-quality excavator repair and maintenance services.

Professional excavator technical support and purchasing services

The machdealers platform provides high-quality services for your excavator purchase, repair, and after-sales support.