U35 vs KX163-5: Verification Differences That Actually Change Your Inspection Bill

What I am looking for from a comparison of two designations aren’t necessarily who’s the best machine, people who know more about a machine’s actual dyno data than I do have already done that, what I want to know is what is right for me to buy because in the end, I’m standing on a gravel pad at 8 in the morning. But what is important is which verification procedure remains on one serial number, on one pad and with no facility to cancel this out–with your deposits paid for in your pocket. More specifically, the bill you ultimately pay is based on the measurement (which you saw) and not on what a page says it measures.

The Array is an Order of Hands that Catches things: 6 Rows One Pair of Hands

The first three rows are known as Undercarriage, Attachment Duty Class, Structure & Welds.

Undercarriage first and undercarriage as system NOT parts list. If an inspector were to look at the height of track shoes and reported it as“checked,”it would be a one gauge of four. Those four consume each other–height of shoes, profile of the shoes’ inside shoulders (roller flanges), idler wear ring, sprocket tooth geometry–a machine run in wet clay demonstrates a chain of destruction that a machine doing the same number of hours in dry hardpack simply won’t show. Same hours. Different bill. When a pad is in contact while operating in slurry, the chain clearance is scoured open between the pin and bush, this causes the chain to stretch itself and this subsequently lowers the chain on the flank of the chain tooth rather than lifting it on the root of the chain and this brings about premature failure of the sprocket early while there is still meat left on the shoe.

Next up attachment duty class, and the designations, here do not separate out gravitas as per brochures, but that isn’t the only problem here. You don’t check the duty class off of anything. You test it by checking the requirements that were used to define the attachment and the connecting structure was designed according to the requirements. The case of pin and the bush slop at the coupler, the thickness of the boss at the mounting ears, the condition of the bucket heel(s) and side-cutters are all monuments and signs of duty. If a machine that is being resold as a general purpose utility vehicle has a bucket rebuilt 2 times, then this machine has not been a trenching machine all of its life.

In fractures where a discontinuity has formed, the fracture face holds the secrets of its history. When the crack originated at the weld toe and extended into the parent material the story is the same—it was a fatigue story begun at a stress riser that someone left at the weld toe. Crack began at the root of the threads: A fastener story, someone let a bolt go or the hole gave way and it was torqued in. The witness mark of the washer, below a structural bolt will show loss of pre-tension first, before the structural bolt will show you anything as the washer has been moving due to pre-tension loss. As far as I was concerned, it is the first message received that is legible, on such a hot day and worth much more than 10 minutes with a light and a mirror.

Swing Bearing, Hour Record, Service Evidence–rows 4–6

Backlash does not exist till you feel it and hear it. Load the tip, boom out and rock it. What you’re looking for is the“slack”between the time the swing motor starts to take up and the time the house“moves”. At the turn, you hear a sound, too, although it’s not a knock; it’s a soft-sounding double-tick as the rolling elements travel across a section of the track that’s been worn smooth. Listen and STOP before going under.

With a grease leak showing up on the seal line, there will be no need to use a dial indicator to determine what the race’s doing. Some new grease squeezing out is OK. What you don’t want is to find that the grease is dried up at the seal, a black cracked collar that no longer seals and is building up grime. That grit persists in and persists on–it penetrates slowly and thoroughly.

The record next is the hour record, where the buyer is lied to the politest. The auditor is working on the machine for the hours that it earned in wear. Pedal rub, seat bolster collapse, polish marks on the travel levers, hose date marks on pressure lines, screw witness marks on the meter, wear mark on the boot heel where the bolster was positioned. Tie into triangles everything! If a low reading is lying on a hosedown sizzling in the sun and a bolster is bent down, it’s a machine that’s been around–and like most things I know, I wouldn’t credit either of the two numbers.

The last piece of evidence for a service is “Service” and it’s the line that delineates a serviced machine from a cleaned one. Clean is easy. A hydraulic filter canister with a handwritten date by the filter, marker, and initial, OIL on the dipstick that is dark in color but can still be seen through—service. The opposite is a machine that has been newly scrubbed down, so that every bit of grease is cleaned, every engine bay spotless of dust; which means somebody didn’t want you reading what the dust had to say!

There are three rows in a deal that can kill it alone, one is a hooked sprocket with a stretched chain, second is a swing bearing with dry seal-line grease and a reversal tick and the third is any type of weld crack in the boom root. All else is hawking. The three of those guys are walking.

There is a “spec sheet”, a value declared and a value measured and the spec sheet is entirely on the declared side. Operating weight is a typical practice, not a measurement taken. It will really vary based on manufacturer and parts of the machine, such as whether the counterweight is standard or not, or whether the machine was quoted with or without attachment, or the fuel and operator assumptions the manufacturer made. Let’s compare two manufacturers’ numbers and you’re comparing two conventions! It has not yet been attainable to either, a scale.

Let’s check out in which manner the comparison column is dishonest. The difference between the two types of class is a difference in reality and no one would want to conceal that. The difference within the class is however great. Machines are individuals. A well-maintained“smaller”unit may do just as much, if not more, for you on a Tuesday afternoon, as might a hard-worked“larger”unit—and it may also be the other way around.

I will acknowledge the proper applications. Declared data can be useful for parts matching, planning trips, using attachments, determining if the item fits onto your trailer, and if it will fit through your gate. Logistics are made use of it. Do not rely upon it to make a determination as to whether or not this machine is worth its price.

I am now sitting here with an O-ring on my bench and, in a miniature all of the argument.

It was dismounted from a grease line which led to a swing bearing and it has been lying in a scrap of shop towel, beside a cold cup of coffee for two hours now. It is the behaviour of cross-sections that I am interested in. Take between thumb and forefinger and release–a healthy one will return with a snap. This one will then move back the majority of distance and pause…That pause is compression set. The elastomer is now permanently molded in a new shape. After some time the heat was so great that the polymer chains rearranged and were no longer eager to go home.

The second story is under a loupe. Tiny circular cracks along the periphery that opened to the heat source and an increase in hardness which results in a smoother surface than usual–when the surface is scratched with a fingernail it has less of a tacky feel. Where the fitting was crushed against the boss, there is a flat having a feathered border; indicating that the shaft of the fitting was slightly misaligned when it was pulled down to create the flat. Not much. Enough. That is the reason why I did not find the seal to “gall” anywhere but there, that off-axis crush, and that is why when I fit a new seal I make sure to check the fitting for galling before I “call it a day!”

At this point (and this is where I cut off a seal story) that O-ring is the same component, performing the same function, on both machines. These are all similar across a single cross section, failure logic, off axis crush and thumb and forefinger test. That diagnosis doesn’t include the designation on the side of the house.

Share this article

Table of contents

Kevin Chen

Chen Kaiwen holds a bachelor’s degree. He frequently travels to construction sites around the world to provide customers with high-quality excavator repair and maintenance services.

Professional excavator technical support and purchasing services

The machdealers platform provides high-quality services for your excavator purchase, repair, and after-sales support.