320D vs 320D2L — Which Chassis Configuration Survives Your Duty Cycle

By Published On: October 28, 2026Categories: Excavator Buying Guides

Introduce point 1 – Debunk the myth.

Please Note: The L does NOT stand for long tail swing. It is NOT long reach. The buyer looks at the letter, knowing that it’s either a counterweight or the boom and makes a swing clearance decision based on a badge. The undercarriage is represented by the L. The longer the track frame, the more shoe it will have on the ground. That’s it. It’s the only letter! That geometry pays off is the truth. But the price isn’t just as fictional as is their purported worth, and the two prices don’t often occupy the same paragraph on a dealer’s listing page. Review the “flotation row” two times. It’s over sold to the uninformed purchaser who is looking for the wrong reason to buy. Longer track frame means that it’s spread out across a larger area, reducing the amount of pressure going through the ground, and that equates to less sinkage in the soft stuff. All true. All mechanically sound. Then you come out to where the soft layer is a couple inches above hardpan, and the same machine floats no problem, as the hardpan is taking up the load – and you have paid for flotation you’re not using! Initially the Ground pressure facility appeared good to me. I have since come to realize that it means “rummy”, and not a promise, since it is assuming a “clean, level, uniform surface” not really found in the real world except in laboratories.

The $22k Flotation Fallacy

The long frame comes into its own when working on slopes and side lift, and when you have experienced the wave, there aren’t many arguments! With a machine on a solid cross-slope, load the bucket off to the side and before it shows up on your load chart, you’ll be able to feel it in your seat. The long frame relays you no later. In any job in which that ‘later’ is most of your production the suffix is all that counts. There is no one who measures offset attachment load or tail-swing geometry until the trench wall protests. People in a lane, with a wall on one side and a curb on the other side, for which a machine was specified with a side-shift offset boom, are the most vulnerable to torsional load in the boom foot and swing bearing, something a straight boom may have avoided. I have heard that ‘Can you feel it’ warning of that fatigue many more times than I have read on an inspection sheet. Small dry knock in swing 1/per revolution, @ a specific angle – absent when the grease is fresh – back 2 shifts later. That doesn’t get written up.” Everybody hears it. One of the counterintuitive results from my notebook – though this comes from one swing bearing grease sample from one site on one type of unit used in quite a high grit environment: on the long-track machine the grease samples were visibly discoloured at the earlier time point of the service interval compared to a standard machine serving at the same site. The same grease, same hours and yet different results. I’m going to go with the added frame length altering how the machine loads and unloads the bearing in a turn and would need about a dozen machines before I’d stand firm on that on argument.

Underspecifying conditions under the car for ground conditions:

Valuing a run of the mill tail-swing purchase should be thumped back by three ground signatures without any soil report needed and I do not need a soil report to identify any of them. The rumour is that the site is referring to the bearing surface. When your operators are discussing the locations of “Can Track” and “Can’t Track” instead of “Need to Dig” you’re controlling ground pressure rather than production. When the water table is high so that the tracks collapse during the nighttime, it’s territory where footprint is a more important consideration than reach. Purchase the lengthy frame there and the machine remains on top of the job. Purchase the standard one – enjoy a season of building haul roads that weren’t in your design, towing tracks off that you didn’t expect to drag, or – surprise the owner – hot loading within the machine’s lifting chart and tipping it anyway because the chart assumed that the machine was on ground on which your shoe could ride.

Puts more than necessary of transport and permit cost into a duty cycle where it is not required. The other sin is quieter, and careful folks commit it; hence it hurts more. Longer frame, bigger shoes and all of a sudden, a phone call becomes a permit application, a trailer is towed from farther off, in some jurisdictions, a pilot car precedents the move, and, a move may be at night because of curfew. I would not quote any number, that figure fluctuates depending on the state line that you cross as I have seen it upswing and downswing to be quite embarrassing. What I will say, is that it is a cost per move, and it does this in a manner which nobody provides correctly on their purchase. Transitions twice a year for a machine – you would never sense the transition. Drive it twice a month throughout a metro area, and you’ll feel it any time you get in it, and the undercarriage you paid for will never see the light of day. My first question is: what do the day’s listing look like after a week of rain and a week of no errors, not how the site looks when you purchase the machine, but how the worst site that you will bid this year looks after a week of rain.

What I’ll be putting on the Lowboy Tomorrow

Now you have a checklist, that fits easily into your jacket pocket! Un-click the serial break, panel boot, and then the sprocket tooth on your thumb and then finally the dust boot on the track adjuster. 4 minutes on the machine equals 1 week of pages listing. Same goes for our inventory: machines that don’t pass the test don’t get put on the page – not out of patriotism, just don’t want to put myself on the line answering a call home from a machine that doesn’t pass the test. With his word, that filter excludes more inventory than purchasers foresee, which explains why there’s a less amount of inventory than what’s being shown in the search results. So it’s coming down to not comparing one article to another. It’s narrow.

See what’s available in 320 class and experience what I have described first-hand: the tooth edging, the boot, the half second of nothingness before the lights of the monitor turn on. If like for most buyers the question that is left still unanswered is an undercarriage question: Filter all the available units of 320D and 320D2L and read the track frame length before reading the price. Two different machines for two badges. I’m going to stop just one caveat. My read is from where I’m at and it’s in a non-stealth section of the country–clay soil, rain. Our’s is rock and dust and a hundred kilometres of haul road. Come with your worst site description (the one that’s after a week of rain”!) and we will compare the units on the ground with that one! Request history file of the service. Request the Sample of the swing bearing grease. If either is deflected, you found out something you wouldn’t know with the aid of any walkaround.

Share this article

Table of contents

Kevin Chen

Chen Kaiwen holds a bachelor’s degree. He frequently travels to construction sites around the world to provide customers with high-quality excavator repair and maintenance services.

Professional excavator technical support and purchasing services

The machdealers platform provides high-quality services for your excavator purchase, repair, and after-sales support.