Checking a Used Excavator’s Real Hours: The Wear Points That Cannot Be Reflashed

By Published On: October 28, 2026Categories: Excavator Buying Guides

The call was after 3 weeks of delivery. This guy on the line had bought the machine on a Tuesday and had been stranded for two hours in a gravel yard without any support and was saying that his guy engines were whaling when under load, but his monitor in the cab was in the low four thousands. I kept telling him to press the phone down more so that I could hear it, and I found the upward-dipping-downward whine, a periodicity, a drive with real-time on it is building—this is a drive with a fresh setting of bearings doesn’t, maybe every second and a half while the teeth go round. After which, with one question I asked. If he were to have kicked at the hose jackets. Silence. He then explained that the seller had provided him with a printout service record and provided a stamp of it. That’s the form that this issue comes on every year the machine makes it through to the basic configuration year and does not change. The panel is a number that someone is able to enter. The individual comes to face a rubbering that must be lived with.

The Dashboard Lie vs. Hose Fossil Record

No equivalent to “lie about” time for rubber. Hose is molded, and the process articles date code—the little block of numbers pressed a hand’s breadth back from each end of the hose, and set up on tooling by the person who extrudes the hose get re-stamped periodically. Wiring a circuit in and out requires the use of one hand tool, all sort of cursing, and basically a whole day on a machine which is already dirty. To pull boom’s return line down and tilt jacket in to the light. Now it had turned chalky, a bit like an old block of chocolate and the code relating to the ferrule was beneath the “build window” the seller had given. Good sign. In that I saw the code for the line feeding the Aux circuit, which all operators claim not to use, and it was different by a whole span of years there.

The second tell is the depth of the bite on the crimped collars and one that few buyers consider. The crimps are manufactured by a factory and are at a set tonnage and the collar has a uniform bite around its circumference; there is a sharp shoulder at both ends of the collar press. A shop re-crimp doesn’t have as deep a bite, and can usually be felt next to the collar by the thumbnail and won’t be apparent in the photographs. To be honest, 50% of the machines that I study don’t pass this test as well and nobody bats an eyelid, because hose is a maintenance item and maintenance items are replaced at regular intervals. True enough. But a hose doesn’t or can’t wear out by itself. What happens is that hoses fail where other things are failing; it’s not as if the code is “fresh hose, run fresh hose” — it’s that the brand new hose is under the dirt – old hose with the same code – on a machine that is said to never get used. I do recall half of a sandwich in my left hand at the time I was judging that date code – not the most elevated of positions in a tech inspection, but a very real one.

Rod Chrome, Wear with a Direction, Pump Geometry

On a cylinder rod, pull back the wiper seal and check the chrome that ordinarily is concealed by the seal. Any factory chrome in the grinder will have a fine to small sheen pattern under work light that is sort of a traverse mark from the grinding wheel — The light will reflect, not as a mirror, but as a sheen with direction. Unlike a braid, a re-chromed rod has a different “signature” since the plating shop will grind after re-chroming and the marks will be shallower and they will likely be crosshatched; there’s an edge line of the plating around the gland, where the new chrome ends and the original surface begins.

That’s the confession line! It’s also defined at a fixed distance from the seal and if that line falls within the area of the seal travel then the wiper had been operating in the step area for as long as the machine had been back in service – and that’s a factor other than hours and a bad situation to boot. The direction of wear on the pump and valve body is nearly irrefutable. The reason the land is called a spool is that flow will always push in one direction, wearing a slope to one side of the land. The scuffing on the slipper outlines the range of operating angles the pump will have actually operated in — if a trencher is operated on a steady angle then there will be a band of bright metal scuff around the slipper, and if it is operated in a variety of angles a wide, soft scuff grade will be seen around the slipper. When a rebuilt unit, put into the same casing, begins to write another sequence over the previous one, the two sequences quarrel in an obvious manner – having (seen what he tells his friend twice) repeatedly viewed twice it becomes obvious. A new rod is coated with chrome which is a mirror. This is an honest one that has as name Chrome.

There was one more machine repair that took place on Thursday, Repair Yard Diary.

Two bays away a crew had a stick cylinder on the bench that had a cracked gland nut and a drip pan below to collect the remaining oil. The discussion was about re-sealing the entire cylinder, or just the wiper and it was an argument that had the familiar form of these arguments: one man saying it’s all good to go until Friday and another saying he’s done it twice. I walked over as it was only the rod extension was out and I wanted to have a look at the chrome for the seal. It has some very fine scratches, but no deep scratches, no edge line of plating, and has a set of grind marks throughout. This gave it its original chroming, which it had never had repeated. The nuts on the gland were in the condition of having the factory staking. No one had been inside that for quite a while and the hours on this one, I’d already set my face to trust. Sometimes the metal matches the paperwork and then you’re not necessarily looking for departures to strive to walk them and rather, you’re considering the offer.

Share this article

Table of contents

Kevin Chen

Chen Kaiwen holds a bachelor’s degree. He frequently travels to construction sites around the world to provide customers with high-quality excavator repair and maintenance services.

Professional excavator technical support and purchasing services

The machdealers platform provides high-quality services for your excavator purchase, repair, and after-sales support.