Filter
Industry & Category
Country
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
Brand
- (2)
- (1)
- (1)
- (2)
Model
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (2)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (2)
- (1)
- (2)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
- (1)
Condition
- (1)
- (3)
- (2)
Year
- (2)
- (1)
- (1)
- (1)
- (1)
Price
Hours
11/2 ton mini excavator with diesel engine
We’ve found 6 products you may like
The Zero-Trust Filter is names after the Hour Meter, which has withstood this threat better than others.
According to the listing it is 3000 hours. We don’t read that number. We don’t pay attention to the label. The photo set is disregarded. Seller’s maintenance binder is not taken into consideration. Digital panels on this the weight class take ten mins to rewrite. Ten. One laptop. One harness. A single Chidden tool file from forum. Done.
Connects with the ECU. We retrieve the file of runtime log that is stored. Key on cycle count is cross referenced with throttle-load histogram. Shadow data is left whilst hours are rolled back. Always. The man at the computer running a laptop is editing the display counter. He hardly writes on the cycle book. He doesn’t often even use the fault archive.
The rest is performed by the hydraulic oil. We sample from return and reservoir (our sampling process). Viscosity breakdown. Ferrous particle count. Oxidation. This machine ran well beyond the meter with burned fluid and high ferrous load, and was reading 2800 hours. Wear does not lie. Counters do.
Anti-Fraud Signal — MachDealers Inventory is a cross-model function that alerts you to fraudulent machine models.
This lot is not considered to be one bucket. Filter by Model. Five Way Exposure Profile.
305.5E2. Dealer-network iron. By OEM write log, logs are returned. This leaves confidence ceiling at a higher level. At present we still are pulling the data.
CAT 305.5E. Same platform family. Same retrieval path. Same procedure. Access to port, run time stored and fault register. We do a comparison of all three.
KX163-5. Diagnostic port access is via direct access. It’s quite common to use aftermarket tooling. The clocking is very active on this model, at street level. Cross checking with Fault History Register. Not the display.
SK55SR. Short-radius unit. High rental-fleet turnover. When dealing with rental equipment each machine’s hard duty cycles are recorded. Cycle count is performed and cross checked. Mandatory.
SY55U. Younger to Western secondary courses. Documentation tracking the iron is maintained by ECU. The quantity of paper verification is insufficient. The wear in the physical state is used. Undercarriage. Pin/bushing play. Noise of the pump when working under load.
One listing page. Five trust floors. The Country filter will then move them once again. If a unit crosses two reseller borders before it makes it to here it has two additional opportunities to have a meter changed.

Data sources for the table above:https://www.rbauction.com/pdp/2015-link-belt-145×3-tracked-excavator/15335385
Rejection Red Lines
- List hours is not consistent with ECU Compiled Time. Walk away. No negotiation.
- Number of Ferrous Particles for hours stated not consistent. Reject.
- Lower legs worn in a way that is not in line with the meter. Worn sprocket and new shoes. New paint on rounded paint rollers. Reject.
- There is a devoid of fault archive above 2,000 hrs. Reject. There are no ‘clean histories’ in field.
- Before LOI, Seller will refuse access to ECU. Reject.
- No records of any OEM work. No telematics export. Not assessed by a third party inspection report. Supplies it at the price of a 5000 hr. machine. The panel reading is not important!

We buy iron. Not screens. Both the meter is a claim. Facts of the fluid, the pins, the number of cycles. We pull the data. We sample the oil. Or we take over someone’s else’s problem.



